DRYMATIC II MKII
- Quiet, Intelligent & Energy-Efficient
- Heat & Air Exchange to Optimise Drying Conditions
- Operate in Neutral or Negative Pressure
- Excels in Class 4 Drying Situations
- Flexible System with a Range of Attachments
- Stackable Roto-moulded double-skinned housing/body
- Weight is only 25 kgs
- Portable, plug into a 10Amp Power Outlet (no gas or diesel required)
- Touch-safe Heater Outlet
- Quick-fix hose connection
- Wheels for easy manoeuvrability
- Significantly reduces the drying life cycles
- Enhance your Experience with the 7 Port Adaptor Kit – turn your Drymatic II into a Push/Pull cavity drying system!
Drymatic II includes 3 x 150mm grey hoses, 1 x 150mm Foil hose, 4 x roto-moulded screw-in connections, 4 x Jubilee clips and a sturdy blue hose bag
FEATURES
DRYMATIC II MKII - THE RIGHT TOOL FOR THE JOB
Recirculation Mode
The area is continuously heated up until either a temperature or humidity limit is reached.
During Recirculation Mode the Drymatic II takes air in from the Room Intake, moves it through the machine to measure Temp and RH and then reheats the air to raise ambient temperature. It stays in this mode for whatever timings you set or until preset conditions are met.
Exhaust Mode
Exchanging the warm, humid air with warm, dry replenishment air. The Drymatic II can cycle between these modes to maximize the amount of water removed from the area.
In Exhaust Mode the Drymatic II takes air in from the Room Intake and purges it straight through the machine to outside via the Outside Exhaust. At the same time, the machine takes in replenishment air from an unaffected area (Outside or another room maybe) and heats that air before pushing it into the drying chamber.
The default cycle is 2 Hours Recirculation (Reheating) and 8 Hours Exhaust (Purging). These settings can be adjusted depending on the circumstances eg if the air is wet exhaust more and recirculate less if it's drier air it should recirculate more to keep the energy in the chamber.
Now you can program your own recirculation and exhaust mode timings. If you want to put the environment under slightly negative pressure the machine can go in the space being dried and you simply leave off the Outside Intake pipe and let the building space breathe naturally.
There are a number of ways to set the Drymatic II up to suit different situations utilising the Y piece kit on all jobs makes the machine work better by pulling down the relative humidty more evenly.
THE TWO SIDES OF THE DRYMATIC II
- The side with the foil heater hose is the Heater Outlet (Heated Air) aim away from room intake. Next to that is the Room Intake (Air from Drying Chamber make sure you always connect a Y Piece kit so you can pull the wet air from multiple areas)
- On the other side of the machine is the Outside Exhaust (Wet Air from Room) to exhaust out of the drying chamber eg. window, dog door, high temperature dehumidifier, air condition room etc and the Outside Intake (Replenishment Air) this air needs to be dry air this could be in an unaffected room, outside or if no choice the actual drying chamber
There are two distinct modes of operation, Recirculation and Exhaust.
DRYMATIC II Y PIECE ADAPTOR KIT
The Y-piece splitter allows you to split your room intake from separate rooms from the Drymatic II. by doing this with the Y-piece this allows you to lower the specific humidity more evenly.
INCLUDED Y Piece Adaptor 3 x 5m 150mm Hose 3 x Jubilee Clips 1 x 150mm to 150mm Joiner 1 x Carry Bag
DRYMATIC II EXHAUST ADAPTOR KIT
The Exhaust Adaptor allows the Drymatic II exhaust outlet to be reduced from 150mm to 100mm which allows you to exhaust your Drymatic II into a downlight, toilet window vent etc.
INCLUDED 1 x 150mm to 100 Reducer Adaptor 2 x Jubilee Clips 1 x 6m of 100mm Hose
DRYMATIC II INJECTION ADAPTOR KIT
Turn your Drymatic II into a Push/Pull cavity drying system using our 7-Port adaptors and hose kit. Create Positive, Negative or Balanced drying regimes by manipulating the number of connections fitted. Controlled heated airflow into kitchen cabinetry, cavity walls, subfloors, ceiling voids and much more.
INCLUDED 2 x Drymatic II Multi-port Adaptor 38mm 30m of 38mm Hoses 14 x Hose Cuffs 1 x Carry Bag 14 x 38mm to 25mm Connectors and 2m of 25mm Hose
BOOST BAR MKII
We are pleased to announce the launch of the Drymatic Boost Bar MKII! The Boost Bar MKII 6 heater unit is the next generation of the Boost Box; further expanding our ability to deliver targeted heat to wet structure. Drymatic Boost Bar is stackable. The machines roto-moulded chassis allows for stacking in two orientations to give more stability to your equipment whilst in transit.
The latest technology with the user-friendly touch screen Interface. The home screen shows you;
- Feedback on Air In/Air Off Temperatures
- Heater Power Readout and Number of Heater Banks Running
- Machine Status
- Airflow Detection
- Hours Run and KWH Meters User Controls
- Maximum Temperature Limit
- Current Limiter (for situations where reduced power is available on site)
- Machine Life Data and Factory Diagnostics Graphical Display
- Average Temperature Differential by Day
- Power Consumption by Day
The Boost Bar also has a pin lock facility, this prevents machine settings being adjusted by homeowners and or others the code for the pin lock is 1 pause 2 pause 3 pause 4
The Drymatic Boost Bar can be used with an Air Mover, Drymatic Mat systems, Drymatic 3 Port 150mm Adaptor Drymatic 4-Port 100mm Adaptor, Drymatic 5-Port 50mm Adaptor, Drymatic 12-Port 38mm Adaptor, Drymatic 22-Port Injection Kit and Drymatic 90deg Adaptor. The Drymatic Range of Adaptors allows you to channel your heated airflow into kitchen cabinetry, cavity walls, subfloors, ceiling voids Drymatic Mats and much more…
Drymatic Boost Bar 3-Port Adaptor Kit
Drymatic Boost Bar’s 3-Port Adaptor gives you the ability to take three separate 150mm channels of airflow to different areas of water damage and multiple mats, split into the 150mm Y Piece, into the 7 port injection, into the step down exhaust then into the 100mm Y Piece.
INCLUDED 3 Port Adaptor 3 x 6m of 150mm Hoses 3 x Jubilee Clip 1 x Carry Bag
Drymatic Boost Bar 4-Port Adaptor Kit
Drymatic Boost Bar’s 4-Port Adaptor gives you the ability to take four separate 100mm channels of airflow to different areas of water damage. Yon can even split this with the 100mm Y Piece.
INCLUDED 4 Port Adaptor 4 x 6m of 100mm Hoses 4 x Jubilee Clip 1 x Carry Bag
Drymatic Boost Bar 5-Port Adaptor Kit
Drymatic Boost Bar’s 5-Port Adaptor gives you the ability to take five separate 50mm channels of airflow to different areas of water damage cavities, down lights and many more areas.
INCLUDED 5 Port Adaptor 5 x 5m of 50mm Hoses 5 x Jubilee Clips 1 x Carry Bag
Drymatic Boost Bar 12-Port Adapter Kit
Using our the 12-Port Adaptor you can take 12 x 38mm outlets and feed them into cavity walls, ceiling voids, kitchen cabinetry and more.
INCLUDED 12 x 38mm Drymatic Boost Bar Adaptor 30m x 38mm Hose 12 x Plastic Hose Cuffs 1 x Carry Bag
Drymatic Boost Bar 22-Port Injection Kit
Using our the 22-Port Adaptor you can take 22 x 24mm outlets and feed them into cavity walls, ceiling voids, kitchen cabinetry and more.
INCLUDED 22 Port Adaptor 60m of 24mm Hoses 1 x Carry Bag
Drymatic Boost Bar 90° (L Shape) Adaptor Kit
Drymatic Boost Bar can be fitted with a 90deg Adaptor that either takes the airflow upwards or downwards under floors.
INCLUDED 4 Port Adaptor 4 x 6m of 100mm Hoses 4 x Jubilee Clip 1 x Carry Bag
Kitchen Kit for the 12 Port Adaptor Kit
INCLUDED 12 x 38mm to 25mm step down connectors and 2m of black 25mm hose.
Drymatic 100mm Y Piece Kit
Using the Y Piece to split of the 4 Port Kit or even the step down exhaust used off the 3 port kit.
INCLUDED 2 x 100mm Y Pieces, 4 x 100mm grey nylon hose, 1 x Carry Bag
Drymatic Luggage Grippers
INCLUDED 8 x Luggage Grippers
DRYMATIC MATS
These floor mats are designed with our legendary heat boost bar and an air mover to target dry hard to dry floors. The technology is heating up the mat changing the surface tension of the floor and by breaking the barrier with our warm micro jets this releases the moisture
Some of the floors that have been successfully saved with this system in record times compared to the traditional systems ( eg air movers and dehumidification) timber floors, concrete, tiles, timber floors under tiles, carpet, underlay, subfloors, even the top down drying of thick wool carpet with felt underlay with a timber subfloor.
These floor mats come in different sizes and can be joined together the 3×1 meter mat is great for hallways and small areas to target even staircase, ceilings, and walls. Their is a mat for all drying situations. One thing you’ll find these are a great noise reduction. These mats create higher vapour pressure on the surface of the material wanting to excape to lower pressure of the air by helping to raise the surface temperature by 10 degrees you are doubling the rate of evapouration.
